Automatic Domestic Water Pump Station with Submersible Pump 3" STM 16 with BRIO PC-13 - RTS, Well Water Set

Product detailed description

The automatic domestic water pump station with submersible pump 3" STM 16 with PC-13 is used mainly seasonally, primarily for irrigation. Submersible pumps for drinking water are used to supply industrial, residential or agricultural buildings with drinking water drawn from greater depths (more than 8m) or piped from a greater distance. The submersible pump 3" STM 16 has increased resistance to sand or other abrasive substances that may be present in the water. The RTS designation on the submersible pump stands for Resistance To Sand (sand-resistant). The submersible pump 3" STM 16 with floating impellers is also designed for new, fresh boreholes, wells, tanks, reservoirs and collection shafts. This pump is suitable for boosting pressure when built into a distribution pipe, and further for domestic or industrial use, irrigation or spraying with water. The hydraulic part of the 3" STM 16 pump is separated from the motor (the pump is not built as a monobloc - in the event of a fault the pump can be easily dismantled). Any repair (which we carry out) need not be too costly and is above all quick, which is a great advantage in the event of a fault. The pump is equipped with thermal protection - a fuse. The submersible pump 3" STM 16 is also suitable for small and medium fire-fighting stations or as part of a domestic water pump station with a submersible pump. BRIO PC-13 type control unit: Automatic switching on and off of the pump when opening/closing a tap Built-in check valve and integrated dry-run protection Pressure gauge Rated current: up to 10A Operating voltage: ~ 230 V ± 10% / 50 Hz Connection: inlet and outlet each with external thread 2.54 cm (G1") Maximum operating pressure: approx. 10 bar Maximum water temperature: approx. 60 °C Switch reset: manual Switch-on pressure range: 1.5 bar Switch-off pressure cannot be adjusted Flow rate: approx. 150 litres/min Dimensions (H x W x D): 15 x 13 x 23 cm Weight: approx. 1.3 kg Protection class: IP65 The electronic switch for monitoring pump operation (in other words a press control) performs the function of a pressure switch, thereby enabling automatic operation of the electric water pump depending on the pressure drop and when water flow in the system stops (i.e. when the device's electrical contacts open and close) - it enables automatic operation of the pump or pump station. The PC-13 press control automat with pressure gauge also provides dry-run protection - it switches off the pump when running without water. This protects the pump from the damage that could otherwise occur when running without water. After switching off, it is put back into operation by pressing the RESET button. A suitable alternative is also: the PC-16 control unit. Product advantages: The PC-13 press control automat with pressure gauge can be used as an automatic unit for pumps and pump stations without a pressure tank (automatic pump station). A major advantage of the PC-13 control unit is its ease of use. The BRIO PC-13 control unit with pressure gauge - press control - has a built-in check valve against backflow of water into the pump. Operation and basic data: The PC-13 automat with pressure gauge starts the pump for approximately 15 seconds at the moment of connection. The pump then starts every time the operating pressure is reached, i.e. when the pressure in the system drops, for example when a valve is opened. Unlike other pressure switches and control units, which switch off on reaching a certain pressure, the PC-13 automat with pressure gauge switches off at the moment the minimum flow value is reached. Once this condition is met, the device delays switching off the device by 7 to 15 seconds. This reduces the frequency of pump starts at low flow rates. Installation: The PC-13 automat with pressure gauge can be installed at any point between the pump and the first point of use, so that the direction of the arrow located on the underside of the device (at the thread) between the two 1" diameter connections corresponds to the direction of water flow. Perfect sealing of the hydraulic connections in the system must be ensured. If a pump with a maximum permissible pressure of 8 bar is used, a pressure reducing valve must be installed at the PC-13 inlet. The device is factory-set to 1.5 bar, which is optimal for most applications. Supplied with cables: 1m cable with plug for connection to the mains 60cm cable for connection to the pump The automatic domestic water pump station with submersible pump 3" STM 16 with BRIO PC-13 includes: Submersible pump 3" STM 16 BRIO PC-13 control unit Connection set for submersible pumps Brass nipple 1" Check valve 1" Transition piece with external thread 32x1" Transition piece with internal thread 32x1" suspension device for submersible pumps