Automatic Domestic Water Pump Station with Submersible Pump SCR-0.25 with BRIO PC-13 + Reducing Valve, for Wells

Product detailed description

The automatic domestic water pump station with submersible pump SCR-0.25 with PC-13 is used mainly seasonally, primarily for irrigation. The submersible spindle pump IBO SCR-0.25 is constructed as a robust, maintenance-free pump with a wide range of uses. For this automatic domestic water pump station to work reliably, a pressure reducing valve must be used in this set upstream of the control unit, and it should be set to a max. pressure of 6bar. A 1" water pressure reducing valve is included in the package. Use: for pumping drinking and utility water practical and versatile use suitable for setting up water supply systems in family houses, cottages, summer residences, schools and farm buildings for supplying water for spraying for garden irrigation for fresh, new wells and boreholes BRIO PC-13 type control unit: automatic switching on and off of the pump when opening/closing a tap built-in check valve and integrated dry-run protection pressure gauge rated current: up to 10A operating voltage: ~ 230 V ± 10% / 50 Hz connection: inlet and outlet each with external thread 2.54 cm (G1") maximum operating pressure: approx. 10 bar maximum water temperature: approx. 60 °C switch reset: manual switch-on pressure range: 1.5 bar switch-off pressure cannot be adjusted max flow rate: approx. 150 litres/min dimensions (H x W x D): 15 x 13 x 23 cm weight: approx. 1.3 kg protection class: IP65 The electronic switch for monitoring pump operation, in other words a press control, performs the function of a pressure switch, thereby enabling automatic operation of the electric water pump depending on the pressure drop and when water flow in the system stops (i.e. when the device's electrical contacts open and close) - it enables automatic operation of the pump or pump station. The PC-13 press control automat with pressure gauge also provides dry-run protection - it switches off the pump when running without water. This protects the pump from the damage that could otherwise occur when running without water. After switching off, it is put back into operation by pressing the RESET button. We recommend using it in clean water systems without impurities and sediment; otherwise a suitable filter must be installed on the inlet side of the device. Advantages: can be used as an automatic unit for pumps and pump stations without a pressure tank (automatic pump station) ease of use built-in check valve against backflow of water into the pump Operation and basic data: The PC-13 automat with pressure gauge starts the pump for approximately 15 seconds at the moment of connection. The pump then starts every time the operating pressure is reached, i.e. when the pressure in the system drops, for example when a valve is opened. Unlike other pressure switches, which switch off on reaching a certain pressure, the PC-13 automat switches off at the moment the minimum flow value is reached. Once this condition is met, the device delays switching off the device by 7 to 15 seconds. This reduces the frequency of pump starts at low flow rates. Installation: The PC-13 automat with pressure gauge can be installed at any point between the pump and the first point of use, so that the direction of the arrow located on the underside of the device (at the thread) between the two 1" diameter connections corresponds to the direction of water flow. Perfect sealing of the hydraulic connections in the system must be ensured. If a pump with a maximum permissible pressure of 8 bar is used, a pressure reducing valve must be installed at the PC-13 inlet. The device is factory-set to 1.5 bar, which is optimal for most applications. Supplied with cables: 1 m cable with plug for connection to the mains 60 cm cable for connection to the pump The automatic domestic water pump station with submersible pump SCR-0.25 with BRIO PC-13 includes: Submersible pump SCR-0.25 BRIO PC-13 control unit 1" water pressure reducing valve Suspension device with cable length Connection set for submersible pumps Brass nipple 1" Check valve 1" Transition piece with external thread 32x1" Transition piece with internal thread 32x1" suspension device for submersible pumps