Automatic home water pump station with submersible pump 3" 3Ti-17 with BRIO PC-13 - RTS, well and borehole set

Product detailed description

Automatic home water pump station with submersible pump 3" 3Ti-17 with PC-13 is used mainly seasonally, primarily for irrigation. Submersible pumps for drinking water are used to supply industrial, residential or agricultural buildings with drinking water obtained from greater depths (more than 8m) or supplied from a greater distance. The submersible pump 3" 3Ti-17 has increased resistance to sand or other abrasive substances that may be present in the water. The submersible pump designation RTS means (Resistance To Sand). The submersible pump 3" 3Ti-17 with floating impellers is also designed for new, fresh boreholes, wells, tanks, water reservoirs and collection shafts. This pump is suitable for increasing pressure when built into a distribution pipeline, as well as for domestic or industrial use, irrigation or water spraying. The hydraulic part of the 3" 3Ti-17 pump is separated from the motor (the pump is not built as a monoblock - in case of a fault, the pump can be easily disassembled). Any repair (which we carry out) does not have to be too costly and is above all quick, which is a great advantage in the event of a fault. The pump is equipped with thermal protection - a fuse. Submersible pump 3" 3Ti-17 is also suitable for small and medium fire-fighting stations, or as part of a home water pump station with a submersible pump. BRIO PC-13 control unit: Automatic switching the pump on and off when opening/closing the tap Built-in check valve and integrated dry-run protection Pressure gauge Rated current: up to 10A Operating voltage: ~ 230 V ± 10% / 50 Hz Connection: inlet and outlet each with external thread 2.54 cm (G1") Maximum operating pressure: approx. 10 bar Maximum water temperature: approximately 60 ° C Switch reset: manual Switch-on pressure range: 1.5 bar Switch-off pressure setting not possible Volume flow: approximately 150 litres / min Dimensions (H x W x D): 15 x 13 x 23 cm Weight: approximately 1.3 kg Protection class: IP65 The electronic switch for monitoring pump operation, also called a press control, provides the function of a pressure switch, enabling automation of the electric water pump's operation depending on the pressure drop and the stopping of water flow in the distribution system (i.e. when the device's electrical contacts open and close) – it enables the automatic operation of the pump or water pump station. The automat, press control PC-13 with pressure gauge, also provides dry-run protection - it switches off the pump when running without water. This protects the pump from damage that could occur when running without water. After switching off, it is put back into operation by pressing the RESET button. We recommend using the automat, press control PC-13 with pressure gauge, in clean water distribution systems free of impurities and sediment; otherwise a suitable filter must be installed on the inlet part of the device. A suitable alternative is also: PC-16 control unit. Product advantages: The PC-13 press control automat with pressure gauge can be used as an automatic unit for pumps and water pump stations without a pressure tank (automatic water pump station). A major advantage of the PC-13 control unit is its ease of use. The BRIO PC-13 control unit with pressure gauge - press control - has a built-in check valve against water flowing back into the pump. Operation and basic data: The PC-13 automat with pressure gauge starts the pump for approximately 15 seconds at the moment of connection. Afterwards, the pump starts every time the operating pressure is reached, at the moment when the pressure in the system drops, for example when a valve is opened. Unlike other pressure switches and control units, which switch off when a certain pressure is reached, the PC-13 automat with pressure gauge switches off at the moment the minimum flow value is reached. When this condition is met, the device delays switching off the equipment by 7 to 15 seconds. This reduces the frequency of pump starts at low flow. Installation: The PC-13 automat with pressure gauge can be installed at any point between the pump and the first point of use, so that the direction of the arrow located on the underside of the device (near the thread) between the two 1" connections corresponds to the direction of water flow. Perfect sealing of the hydraulic connections must be ensured in the distribution system. If a pump with a maximum permissible pressure of 8 bar is used, a pressure reducing valve must be installed at the PC-13 inlet. The device is factory-set to 1.5 bar, which is optimal for most uses. Supplied with cables: 1m cable with plug for connection to the electrical mains 60cm cable for connecting to the pump Automatic home water pump station with submersible pump 3" 3Ti-17 with BRIO PC-13 includes: 3" 3Ti-17 submersible pump BRIO PC-13 control unit Connection set for submersible pumps 1" brass nipple 1" check valve Adapter with 32x1" external thread Adapter with 32x1" internal thread suspension device for submersible pumps