Automatic Home Water System with 3" 3Ti-15 Submersible Pump and BRIO PC-13 - RTS, Well Water Set

Product detailed description

The automatic home water system with the 3" 3Ti-15 submersible pump and PC-13 is mainly used seasonally, especially for irrigation. Submersible pumps for drinking water are used to supply industrial, residential or agricultural buildings with drinking water drawn from greater depths (more than 8m) or brought from a greater distance. The 3" 3Ti-15 submersible pump has increased resistance to sand or other abrasive substances that may be present in the water. A submersible pump marked RTS means Resistance To Sand. The 3" 3Ti-15 submersible pump with floating impellers is also suitable for new, fresh boreholes, wells, tanks, reservoirs and collection shafts. This pump is suitable for boosting pressure when built into a distribution pipeline, as well as for domestic or industrial use, irrigation or spraying. The hydraulic part of the 3" 3Ti-15 pump is separate from the motor (the pump is not built as a monoblock) - in the event of a fault, the pump can easily be disassembled. Any repair (which we carry out) need not be too costly and, above all, is quick, which is a great advantage in the event of a fault. The pump is fitted with thermal protection - a fuse. The 3" 3Ti-15 submersible pump is also suitable for small and medium fire-fighting stations, or as part of a home water system with a submersible pump. BRIO PC-13 control unit: Automatic switching of the pump on / off when the tap is opened / closed Built-in check valve and integrated dry-run protection Pressure gauge Rated current: up to 10A Operating voltage: ~ 230 V ± 10% / 50 Hz Connection: inlet and outlet, each with a 2.54 cm (G1") external thread Maximum operating pressure: approx. 10 bar Maximum water temperature: approx. 60 °C Switch reset: manual Switch-on pressure range: 1.5 bar Switch-off pressure cannot be set Flow rate: approx. 150 litres / min Dimensions (H x W x D): 15 x 13 x 23 cm Weight: approx. 1.3 kg Protection class: IP65 The electronic switch for controlling pump operation, in other words a press control, performs the function of a pressure switch, allowing the automation of the electric water pump's operation depending on the pressure drop and when water flow in the system stops (i.e. when the device's electrical contacts open and close) - it enables the pump or water system to run automatically. The PC-13 press control automat with pressure gauge also provides dry-run protection - it switches off the pump when it runs without water. This protects the pump from damage that could occur when running dry. After switching off, it is brought back into operation by pressing the RESET button. We recommend using the PC-13 press control automat with pressure gauge in clean water systems free of dirt and sediment; otherwise, a suitable filter must be installed on the inlet side of the device. A suitable alternative is also: the PC-16 control unit. Product advantages: The PC-13 press control automat with pressure gauge can be used as an automatic unit for pumps and water systems without a pressure vessel (automatic water system). A great advantage of the PC-13 control unit is how simple it is to use. The BRIO PC-13 control unit with pressure gauge - press control - has a built-in check valve to prevent water from flowing back into the pump. Operation and basic data: The PC-13 automat with pressure gauge starts the pump running for approximately 15 seconds at the moment it is switched on. After that, the pump starts every time the working pressure is reached, at the moment the pressure in the system drops, for example when a valve is opened. Unlike other pressure switches and control units, which switch off once a certain pressure is reached, the PC-13 automat with pressure gauge switches off at the moment the minimum flow value is reached. Once this condition is met, the device delays switching off the equipment by 7 to 15 seconds. This reduces the frequency of pump starts at low flow rates. Installation: The PC-13 automat with pressure gauge can be installed at any point between the pump and the first point of use, so that the direction of the arrow located on the underside of the device (at the thread) between the two 1" connections matches the direction of water flow. A perfect seal on the hydraulic connections must be ensured in the system. If a pump with a maximum permissible pressure of 8 bar is used, a pressure-reducing valve must be installed on the PC-13 inlet. The device is factory-set to 1.5 bar, which is optimal for most applications. Supplied with cables: 1m cable with plug for connection to the mains 60cm cable for connection to the pump The automatic home water system with the 3" 3Ti-15 submersible pump and BRIO PC-13 includes: 3" 3Ti-15 submersible pump BRIO PC-13 control unit Connection set for submersible pumps Brass 1" nipple 1" check valve 32x1" male-thread transition piece 32x1" female-thread transition piece suspension gear for submersible pumps