Assembly manifold/collector for heating radiators - without cabinet - 1xEK; 7-way; nickel
Code: 551755NRelated products
Product detailed description
Assembly manifold for heating radiators - without cabinet, IVAR.CS 501 ND, size: 1" x EK, 7-way, cabinet: P3/N3
- PN 10, T = +120 °C
- the set includes: manifold and collector, mounting brackets, inlet ball valves, end fitting with automatic air vent valve and rotary drain valve, and plugs
- side inlets 1" F
- outlets 3/4" EK
- outlet spacing 50 mm
- plugs 1/2"
- material: nickel-plated brass CW617N
Set for radiator heating or sanitary distribution, without a pump.
Recommended for a temperature gradient of the radiator part of the system +75 ˚C / +65 ˚C
Fitted circulation pump: without pump (not is needed, since pump replaces boiler)
Note: The seller is not responsible for functional defects caused by impurities in the system.
Before every commissioning of the heating system, especially when combining underfloor and radiator heating, it is strongly recommended to flush the whole system according to the manufacturer's instructions. We recommend treating the system with the product GEL.POLY A.P.
Manifolds are installed in cabinets; their recommended lengths are given in the manifold table. Fitting the manifolds at the highest point is practically a requirement (watch out for level changes in the floor plan). The exception is venting small floor loops on a higher storey via a bathroom towel radiator. If the floor system is installed only in bathrooms, it is possible to use a pipe from the return branch of the radiator system with a polyethylene conduit, or a direct-acting temperature regulator can be used at the end of this parallel loop, which will ensure cooling to a low temperature level (caution! it must be thermally separated from the return of the radiator circuit with that it is not thermally affected).
For further information you can go to the questions and answers at https://www.systemova-doska.sk/podlahove-heating/
Additional parameters
| Category: | IVAR CS 501 ND |
|---|---|
| Warranty: | 2 years |
| Weight: | 6.423 kg |
| EAN: | 8595145902477 |
| Outlet spacing: | 50 mm |
| Last price update: | 13.04.2026 1:08:27 |
Product rating
Be the first who will post an article to this item!
Discussion
List of discussions
T
Tibor
Tibor
Dobry den, mam kupeny rozdelovac IVAR CS 501 ND 7 cestný, otazka: je mozne stranovo prehodit ventily a odvzdusnovace zprava dolava? Robim radiatorove kurenie (len prizemie,nemam ziadne poschodie) a chcem sa spytat, co znamena v texte ...Osadenie rozdeľovačov v najvyššom mieste je prakticky podmienkou ... ? Kurenar mi povedal, ze skrinku mozem osadit cca 10cm nad podlahou. Tym padom bude rozdelovac nizsie ako vrch radiatorov. Moze to takto byt? Dakujem.
A
ATRIA
ATRIA
Dobrý deň, Ventily je možné prehodiť stranovo. Prajem pekný deň.
M
mária
mária
Dobrý deň, na vašej stránke ma zaujal vysoký výber vykurovacieho materiálu, o ktorý aj ja mám záujem. Jedná sa o : EPS 100 S hrúbka 40 mm - 215 m2 Systémová izolačná doska UHP 55 210 m2 alebo UHP 54 Potrubie PEX -AL - PEX 16 x 2 1400 m - preto sa chcem informovať o prípadnej zľave pri odbere v takom to množstve a o doprave do okresu Sobraniec. Od výšky zľavy sa bude aj odvíjať ďalší možný nákup 10 cestných rozdeľovačov, a ďalších potrebných vecí k vykurovaniu rod. domu. Preto vás prosím aby ste ma informovali o výške zliav a dodávke do môjho miesta určenia buď mailom alebo telefonicky. Príjemný deň